Cart and Log In

What Is The Difference Between A $40 And A $400 Pressure Transmitter?

Just like cars, the expensive ones usually have good reasonGood question. We get asked this from time to time when someone has seen the advertised prices of cheap pressure transmitters. There are a lot of differences between a cheap $40 transmitter and a robust $400 unit.

It all boils down to accuracy and reliability and the necessary manufacturing processes to go along with them.

The old adage is true; you get what you pay for. When purchasing a pressure transmitter, you’re really buying:

  • Linear accuracy
  • Thermal Performance/Accuracy
  • Stability
  • Materials & Construction
  • Configuration Options

These 5 factors are what increase and decrease the cost of a pressure transmitter. Let’s take a look at each.

Linear Accuracy

This is the accuracy across the full scale that we list on our sensors. Typically, our pressure transducer’s error margin is 0.25% of the full scale. This means that on a 100 psi transmitter, the most the sensors can be “off” is 0.25 psi.

On a $40 pressure transmitter, the best you could expect is an error margin of 1% full scale. That error band is 4X larger.

More importantly, when you loosen one tolerance, you’re frequently loosening all others as well.

Thermal Performance

A cheaper transducer will lack in more than just accuracy. Its thermal performance is also going to be worse. Something like 0.03% FS/°C. In other words, the zero point will shift 0.03% of the full scale for every one degree Celsius change in temperature.

Ours is typically 0.02% FS/°F.

There are 33.8°F for every 1°C. So on a 100 psi pressure transmitter, ours would shift 0.02 psi for every 1°F change in temperature. A $40 unit would typically change a little more than 1 psi for every 1°F change in temperature. That’s about 50X less thermal stability.

Stability

Pressure transmitters experience a phenomenon known as drift. This is a direct result of the bonding layers that attach the sensing elements to the diaphragm. As the bonding layers settle over time, the output of the sensor drifts. The good news is that the drift is predictable and can be fixed by regular calibration.

The bad news is a cheap transducer will drift more, and require calibration more often. Part of our manufacturing process to reduce drift is to cure our transducers. This process includes pressuring our sensors up and down across a wide temperature range. This speeds up the process of settling the bonding layers through accelerated aging.

The curing process adds cost, and isn’t performed for the cheapest pressure transducers. This means the cheap transmitter will drift quite a bit after installation, though it will settle down eventually. So you may see long-term stability specs that are similar to a nicer sensor, but this only serves to hide the lack of stability out of the box.

Materials & Construction

You may have guessed that a cheaper transmitter will be made of lower quality materials, with a cruder construction. For example, our more expensive, robust pressure sensors are made of quality steel materials and built with durability in mind. We use laser welds, high strength bolts and screws, better seals and gaskets (where applicable), and many are filled inside with an industrial potting to seal electronics from moisture and protects connections from vibration.

The cheaper the transducer, the more you need to question quality construction, materials, solder joints, wire connections, etc.

Configure Options

Making a sensor that is configurable adds considerable cost. It increases inventory in both volume and variety. It also increases the complexity of manufacturing products, because you have to build the same product in many different ways.

That’s why the $40 versions just don’t offer the variety of options that you’ll find in a $400+ model.

A Place For Both

This article is meant to answer why some sensors cost more than others. It’s to set the record straight and promote healthy expectations. It’s NOT meant to insult or make fun of cheaper sensors. Those sensors have their place. You just need to know when and where to use each kind.

There certainly are applications that don’t require higher accuracy or strict tolerances on drift. They need only standard pressure ranges, process connections, and electrical connections. For these applications, save your money and buy an appropriate sensor.

For everything else, don’t skimp on quality.

Just remember, you get what you pay for. Make sure you pay for what you want to get.


Looking for a reliable pressure transmitter? Ours have earned their stripes in the field! Check out our durable pressure transducers today:

top photo credit: Benoit cars via photopin cc

Blog Updates In Your Inbox

Contact Details

Phone
888-525-7300
435-753-7300
Fax
435-753-7490
Email
sales@apgsensors.com
Address
1025 W 1700 N
Logan, Utah
84321-1713
USA